1999 Dodge ram 2500 Diesel

From : jryamaha

Q: i have a short bed dodge ram 2500 24valve diesel 4x4. i recently hit a telephone pole dead center. i replaced everything that was wrong. i did not have any problems with the brakes intill just recently. i checked there is no fluid that is leaking that i can see. if i pump the brakes it will build pressure but it only last for a miniute then the pedal will go right to the floor not appling any brakes at all. as you can imagine this is quite the problem. what possibly could be wrong please give me an idea as this truck is my everyday transportation and as of right now i do not have the funds to take it to a shop. .

Replies:

From : Annonymous

sounds like it could be a master cylinder but check to make sure that you arent losing vaccume pressure anywhere as well. did you replace your vaccume pump after the wreck what about the lines if it was a small leak you may still be generating enough pressure for some mild braking but not for prolonged useage. a master cylinder sounds like your best bet though. .

From : tbone

a vacuum leak should not cause that problem. it would make the pedal rock hard like manual brakes not go clear to the floor. -- if at first you dont succeed youre not cut out for skydiving sounds like it could be a master cylinder but check to make sure that you arent losing vaccume pressure anywhere as well. did you replace your vaccume pump after the wreck what about the lines if it was a small leak you may still be generating enough pressure for some mild braking but not for prolonged useage. a master cylinder sounds like your best bet though. .

From : max dodge

a vacuum leak should not cause that problem. it would make the pedal rock hard like manual brakes not go clear to the floor. tbone i didnt follow the thread and im not sure how familiar you are with these trucks. typically iirc that generation of cummins ram has hydraulically assisted brakes; the vacuum pump would have nothing to do with them. i know my 00 has hydraulic assist. -- max join www.devilbrad.com and find out what free exchange of info is all about. there are four boxes to be used in defense of liberty soap ballot jury and ammo. please use in that order. -ed howdershelt author a vacuum leak should not cause that problem. it would make the pedal rock hard like manual brakes not go clear to the floor. -- if at first you dont succeed youre not cut out for skydiving sounds like it could be a master cylinder but check to make sure that you arent losing vaccume pressure anywhere as well. did you replace your vaccume pump after the wreck what about the lines if it was a small leak you may still be generating enough pressure for some mild braking but not for prolonged useage. a master cylinder sounds like your best bet though. .

From : nosey

max dodge wrote a vacuum leak should not cause that problem. it would make the pedal rock hard like manual brakes not go clear to the floor. tbone i didnt follow the thread and im not sure how familiar you are with these trucks. typically iirc that generation of cummins ram has hydraulically assisted brakes; the vacuum pump would have nothing to do with them. i know my 00 has hydraulic assist. my 99 2500 diesel has hydroboost brakes. it runs off the power steering pump. when i stand on the brake pedal hard my power steering gets very heavy. -- ken .

From : bigironram

a vacuum leak should not cause that problem. it would make the pedal rock hard like manual brakes not go clear to the floor. tbone i didnt follow the thread and im not sure how familiar you are with these trucks. typically iirc that generation of cummins ram has hydraulically assisted brakes; the vacuum pump would have nothing to do with them. i know my 00 has hydraulic assist. -- max hydroboost started on the dodge/cummins in 1997. my 96 was vacuum lots of guys with the older trucks are excited about changing to hydroboost im not sure why its a big deal to them both systems seemed to work fine for me. .

From : rick505

first check the brakes master cylinder to see if u are low on fluid if you are check to see if u have a bad brake line check to see if u have a bad caliper if u dont see anything check the master cylinder u may hafto take the mounting bolts off and look at the back of the master cylinder to see if it is wet with brake fluid if it is then u have a bad master cylinder and that would cause it to pump up and as you are holding the brake peddle it slowly fand to the floor and pump it up again and hold it and fade to the floor again hope this helps .

From : tbone

it sounds like a bad master cylinder. what type of anti-lock brakes does it have -- if at first you dont succeed youre not cut out for skydiving i have a short bed dodge ram 2500 24valve diesel 4x4. i recently hit a telephone pole dead center. i replaced everything that was wrong. i did not have any problems with the brakes intill just recently. i checked there is no fluid that is leaking that i can see. if i pump the brakes it will build pressure but it only last for a miniute then the pedal will go right to the floor not appling any brakes at all. as you can imagine this is quite the problem. what possibly could be wrong please give me an idea as this truck is my everyday transportation and as of right now i do not have the funds to take it to a shop. .

From : tbone

im not all that familiar with the diesel models. the op said that his brake pedal was going to the floor and giving no braking action and there were no leaks but if he pumped it a few times he would get limited braking action. i posted that it is most likely the master cylinder and asked what type of anti-lock it had just in case. another poster said that it looked like the master cylinder as well but it could be due to the vacuum pump. i assumed that he was referring to the vacuum boost if this model uses that type and said that a vacuum leak would not cause the pedal to go to the floor. -- if at first you dont succeed youre not cut out for skydiving a vacuum leak should not cause that problem. it would make the pedal rock hard like manual brakes not go clear to the floor. tbone i didnt follow the thread and im not sure how familiar you are with these trucks. typically iirc that generation of cummins ram has hydraulically assisted brakes; the vacuum pump would have nothing to do with them. i know my 00 has hydraulic assist. -- max join www.devilbrad.com and find out what free exchange of info is all about. there are four boxes to be used in defense of liberty soap ballot jury and ammo. please use in that order. -ed howdershelt author a vacuum leak should not cause that problem. it would make the pedal rock hard like manual brakes not go clear to the floor. -- if at first you dont succeed youre not cut out for skydiving sounds like it could be a master cylinder but check to make sure that you arent losing vaccume pressure anywhere as well. did you replace your vaccume pump after the wreck what about the lines if it was a small leak you may still be generating enough pressure for some mild braking but not for prolonged useage. a master cylinder sounds like your best bet though. .